e1000e_phy.h

Go to the documentation of this file.

/*******************************************************************************

  Intel PRO/1000 Linux driver
  Copyright(c) 1999 - 2009 Intel Corporation.

  This program is free software; you can redistribute it and/or modify it
  under the terms and conditions of the GNU General Public License,
  version 2, as published by the Free Software Foundation.

  This program is distributed in the hope it will be useful, but WITHOUT
  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
  more details.

  You should have received a copy of the GNU General Public License along with
  this program; if not, write to the Free Software Foundation, Inc.,
  51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.

  The full GNU General Public License is included in this distribution in
  the file called "COPYING".

  Contact Information:
  Linux NICS <linux.nics@intel.com>
  e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
  Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497

*******************************************************************************/

FILE_LICENCE ( GPL2_OR_LATER );

#ifndef _E1000E_PHY_H_
#define _E1000E_PHY_H_

void e1000e_init_phy_ops_generic(struct e1000_hw *hw);
s32  e1000e_check_downshift(struct e1000_hw *hw);
s32  e1000e_check_polarity_m88(struct e1000_hw *hw);
s32  e1000e_check_polarity_igp(struct e1000_hw *hw);
s32  e1000e_check_polarity_ife(struct e1000_hw *hw);
s32  e1000e_check_reset_block_generic(struct e1000_hw *hw);
s32  e1000e_copper_link_setup_igp(struct e1000_hw *hw);
s32  e1000e_copper_link_setup_m88(struct e1000_hw *hw);
#if 0
s32  e1000e_phy_force_speed_duplex_igp(struct e1000_hw *hw);
s32  e1000e_phy_force_speed_duplex_m88(struct e1000_hw *hw);
s32  e1000e_phy_force_speed_duplex_ife(struct e1000_hw *hw);
#endif
#if 0
s32  e1000e_get_cable_length_m88(struct e1000_hw *hw);
s32  e1000e_get_cable_length_igp_2(struct e1000_hw *hw);
#endif
s32  e1000e_get_cfg_done(struct e1000_hw *hw);
s32  e1000e_get_phy_id(struct e1000_hw *hw);
s32  e1000e_get_phy_info_igp(struct e1000_hw *hw);
s32  e1000e_get_phy_info_m88(struct e1000_hw *hw);
s32  e1000e_phy_sw_reset(struct e1000_hw *hw);
#if 0
void e1000e_phy_force_speed_duplex_setup(struct e1000_hw *hw, u16 *phy_ctrl);
#endif
s32  e1000e_phy_hw_reset_generic(struct e1000_hw *hw);
s32  e1000e_phy_reset_dsp(struct e1000_hw *hw);
s32  e1000e_read_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 *data);
s32  e1000e_read_kmrn_reg_locked(struct e1000_hw *hw, u32 offset, u16 *data);
s32  e1000e_read_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 *data);
s32  e1000e_read_phy_reg_igp_locked(struct e1000_hw *hw, u32 offset, u16 *data);
s32  e1000e_read_phy_reg_m88(struct e1000_hw *hw, u32 offset, u16 *data);
s32  e1000e_set_d3_lplu_state(struct e1000_hw *hw, bool active);
s32  e1000e_setup_copper_link(struct e1000_hw *hw);
s32  e1000e_wait_autoneg(struct e1000_hw *hw);
s32  e1000e_write_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 data);
s32  e1000e_write_kmrn_reg_locked(struct e1000_hw *hw, u32 offset, u16 data);
s32  e1000e_write_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 data);
s32  e1000e_write_phy_reg_igp_locked(struct e1000_hw *hw, u32 offset, u16 data);
s32  e1000e_write_phy_reg_m88(struct e1000_hw *hw, u32 offset, u16 data);
s32  e1000e_phy_reset_dsp(struct e1000_hw *hw);
s32  e1000e_phy_has_link_generic(struct e1000_hw *hw, u32 iterations,
                                u32 usec_interval, bool *success);
s32  e1000e_phy_init_script_igp3(struct e1000_hw *hw);
enum e1000_phy_type e1000e_get_phy_type_from_id(u32 phy_id);
s32  e1000e_determine_phy_address(struct e1000_hw *hw);
s32  e1000e_write_phy_reg_bm(struct e1000_hw *hw, u32 offset, u16 data);
s32  e1000e_read_phy_reg_bm(struct e1000_hw *hw, u32 offset, u16 *data);
s32  e1000e_read_phy_reg_bm2(struct e1000_hw *hw, u32 offset, u16 *data);
s32  e1000e_write_phy_reg_bm2(struct e1000_hw *hw, u32 offset, u16 data);
void e1000e_power_up_phy_copper(struct e1000_hw *hw);
void e1000e_power_down_phy_copper(struct e1000_hw *hw);
s32  e1000e_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data);
s32  e1000e_write_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 data);
s32  e1000e_read_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 *data);
s32  e1000e_read_phy_reg_hv_locked(struct e1000_hw *hw, u32 offset, u16 *data);
s32  e1000e_write_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 data);
s32  e1000e_write_phy_reg_hv_locked(struct e1000_hw *hw, u32 offset, u16 data);
s32  e1000e_set_mdio_slow_mode_hv(struct e1000_hw *hw, bool slow);
s32  e1000e_link_stall_workaround_hv(struct e1000_hw *hw);
s32  e1000e_copper_link_setup_82577(struct e1000_hw *hw);
s32  e1000e_check_polarity_82577(struct e1000_hw *hw);
s32  e1000e_get_phy_info_82577(struct e1000_hw *hw);
#if 0
s32  e1000e_phy_force_speed_duplex_82577(struct e1000_hw *hw);
#endif
#if 0
s32  e1000e_get_cable_length_82577(struct e1000_hw *hw);
#endif

#define E1000_MAX_PHY_ADDR                4

/* IGP01E1000 Specific Registers */
#define IGP01E1000_PHY_PORT_CONFIG        0x10 /* Port Config */
#define IGP01E1000_PHY_PORT_STATUS        0x11 /* Status */
#define IGP01E1000_PHY_PORT_CTRL          0x12 /* Control */
#define IGP01E1000_PHY_LINK_HEALTH        0x13 /* PHY Link Health */
#define IGP01E1000_GMII_FIFO              0x14 /* GMII FIFO */
#define IGP01E1000_PHY_CHANNEL_QUALITY    0x15 /* PHY Channel Quality */
#define IGP02E1000_PHY_POWER_MGMT         0x19 /* Power Management */
#define IGP01E1000_PHY_PAGE_SELECT        0x1F /* Page Select */
#define BM_PHY_PAGE_SELECT                22   /* Page Select for BM */
#define IGP_PAGE_SHIFT                    5
#define PHY_REG_MASK                      0x1F

/* BM/HV Specific Registers */
#define BM_PORT_CTRL_PAGE                 769
#define BM_PCIE_PAGE                      770
#define BM_WUC_PAGE                       800
#define BM_WUC_ADDRESS_OPCODE             0x11
#define BM_WUC_DATA_OPCODE                0x12
#define BM_WUC_ENABLE_PAGE                BM_PORT_CTRL_PAGE
#define BM_WUC_ENABLE_REG                 17
#define BM_WUC_ENABLE_BIT                 (1 << 2)
#define BM_WUC_HOST_WU_BIT                (1 << 4)

#define PHY_UPPER_SHIFT                   21
#define BM_PHY_REG(page, reg) \
        (((reg) & MAX_PHY_REG_ADDRESS) |\
         (((page) & 0xFFFF) << PHY_PAGE_SHIFT) |\
         (((reg) & ~MAX_PHY_REG_ADDRESS) << (PHY_UPPER_SHIFT - PHY_PAGE_SHIFT)))
#define BM_PHY_REG_PAGE(offset) \
        ((u16)(((offset) >> PHY_PAGE_SHIFT) & 0xFFFF))
#define BM_PHY_REG_NUM(offset) \
        ((u16)(((offset) & MAX_PHY_REG_ADDRESS) |\
         (((offset) >> (PHY_UPPER_SHIFT - PHY_PAGE_SHIFT)) &\
                ~MAX_PHY_REG_ADDRESS)))

#define HV_INTC_FC_PAGE_START             768
#define I82578_ADDR_REG                   29
#define I82577_ADDR_REG                   16
#define I82577_CFG_REG                    22
#define I82577_CFG_ASSERT_CRS_ON_TX       (1 << 15)
#define I82577_CFG_ENABLE_DOWNSHIFT       (3 << 10) /* auto downshift 100/10 */
#define I82577_CTRL_REG                   23

/* 82577 specific PHY registers */
#define I82577_PHY_CTRL_2            18
#define I82577_PHY_LBK_CTRL          19
#define I82577_PHY_STATUS_2          26
#define I82577_PHY_DIAG_STATUS       31

/* I82577 PHY Status 2 */
#define I82577_PHY_STATUS2_REV_POLARITY   0x0400
#define I82577_PHY_STATUS2_MDIX           0x0800
#define I82577_PHY_STATUS2_SPEED_MASK     0x0300
#define I82577_PHY_STATUS2_SPEED_1000MBPS 0x0200
#define I82577_PHY_STATUS2_SPEED_100MBPS  0x0100

/* I82577 PHY Control 2 */
#define I82577_PHY_CTRL2_AUTO_MDIX        0x0400
#define I82577_PHY_CTRL2_FORCE_MDI_MDIX   0x0200

/* I82577 PHY Diagnostics Status */
#define I82577_DSTATUS_CABLE_LENGTH       0x03FC
#define I82577_DSTATUS_CABLE_LENGTH_SHIFT 2

/* BM PHY Copper Specific Control 1 */
#define BM_CS_CTRL1                       16
#define BM_CS_CTRL1_ENERGY_DETECT         0x0300 /* Enable Energy Detect */

/* BM PHY Copper Specific Status */
#define BM_CS_STATUS                      17
#define BM_CS_STATUS_ENERGY_DETECT        0x0010 /* Energy Detect Status */
#define BM_CS_STATUS_LINK_UP              0x0400
#define BM_CS_STATUS_RESOLVED             0x0800
#define BM_CS_STATUS_SPEED_MASK           0xC000
#define BM_CS_STATUS_SPEED_1000           0x8000

/* 82577 Mobile Phy Status Register */
#define HV_M_STATUS                       26
#define HV_M_STATUS_AUTONEG_COMPLETE      0x1000
#define HV_M_STATUS_SPEED_MASK            0x0300
#define HV_M_STATUS_SPEED_1000            0x0200
#define HV_M_STATUS_LINK_UP               0x0040

#define IGP01E1000_PHY_PCS_INIT_REG       0x00B4
#define IGP01E1000_PHY_POLARITY_MASK      0x0078

#define IGP01E1000_PSCR_AUTO_MDIX         0x1000
#define IGP01E1000_PSCR_FORCE_MDI_MDIX    0x2000 /* 0=MDI, 1=MDIX */

#define IGP01E1000_PSCFR_SMART_SPEED      0x0080

/* Enable flexible speed on link-up */
#define IGP01E1000_GMII_FLEX_SPD          0x0010
#define IGP01E1000_GMII_SPD               0x0020 /* Enable SPD */

#define IGP02E1000_PM_SPD                 0x0001 /* Smart Power Down */
#define IGP02E1000_PM_D0_LPLU             0x0002 /* For D0a states */
#define IGP02E1000_PM_D3_LPLU             0x0004 /* For all other states */

#define IGP01E1000_PLHR_SS_DOWNGRADE      0x8000

#define IGP01E1000_PSSR_POLARITY_REVERSED 0x0002
#define IGP01E1000_PSSR_MDIX              0x0800
#define IGP01E1000_PSSR_SPEED_MASK        0xC000
#define IGP01E1000_PSSR_SPEED_1000MBPS    0xC000

#define IGP02E1000_PHY_CHANNEL_NUM        4
#define IGP02E1000_PHY_AGC_A              0x11B1
#define IGP02E1000_PHY_AGC_B              0x12B1
#define IGP02E1000_PHY_AGC_C              0x14B1
#define IGP02E1000_PHY_AGC_D              0x18B1

#define IGP02E1000_AGC_LENGTH_SHIFT       9   /* Course - 15:13, Fine - 12:9 */
#define IGP02E1000_AGC_LENGTH_MASK        0x7F
#define IGP02E1000_AGC_RANGE              15

#define IGP03E1000_PHY_MISC_CTRL          0x1B
#define IGP03E1000_PHY_MISC_DUPLEX_MANUAL_SET  0x1000 /* Manually Set Duplex */

#define E1000_CABLE_LENGTH_UNDEFINED      0xFF

#define E1000_KMRNCTRLSTA_OFFSET          0x001F0000
#define E1000_KMRNCTRLSTA_OFFSET_SHIFT    16
#define E1000_KMRNCTRLSTA_REN             0x00200000
#define E1000_KMRNCTRLSTA_DIAG_OFFSET     0x3    /* Kumeran Diagnostic */
#define E1000_KMRNCTRLSTA_TIMEOUTS        0x4    /* Kumeran Timeouts */
#define E1000_KMRNCTRLSTA_INBAND_PARAM    0x9    /* Kumeran InBand Parameters */
#define E1000_KMRNCTRLSTA_DIAG_NELPBK     0x1000 /* Nearend Loopback mode */
#define E1000_KMRNCTRLSTA_K1_CONFIG        0x7
#define E1000_KMRNCTRLSTA_K1_ENABLE        0x0002

#define IFE_PHY_EXTENDED_STATUS_CONTROL 0x10
#define IFE_PHY_SPECIAL_CONTROL     0x11 /* 100BaseTx PHY Special Control */
#define IFE_PHY_SPECIAL_CONTROL_LED 0x1B /* PHY Special and LED Control */
#define IFE_PHY_MDIX_CONTROL        0x1C /* MDI/MDI-X Control */

/* IFE PHY Extended Status Control */
#define IFE_PESC_POLARITY_REVERSED    0x0100

/* IFE PHY Special Control */
#define IFE_PSC_AUTO_POLARITY_DISABLE      0x0010
#define IFE_PSC_FORCE_POLARITY             0x0020
#define IFE_PSC_DISABLE_DYNAMIC_POWER_DOWN 0x0100

/* IFE PHY Special Control and LED Control */
#define IFE_PSCL_PROBE_MODE            0x0020
#define IFE_PSCL_PROBE_LEDS_OFF        0x0006 /* Force LEDs 0 and 2 off */
#define IFE_PSCL_PROBE_LEDS_ON         0x0007 /* Force LEDs 0 and 2 on */

/* IFE PHY MDIX Control */
#define IFE_PMC_MDIX_STATUS      0x0020 /* 1=MDI-X, 0=MDI */
#define IFE_PMC_FORCE_MDIX       0x0040 /* 1=force MDI-X, 0=force MDI */
#define IFE_PMC_AUTO_MDIX        0x0080 /* 1=enable auto MDI/MDI-X, 0=disable */

#endif